general description the MAX14840PMB1 peripheral module provides the necessary hardware to interface the max14840e rs-485 transceiver to any system that utilizes pmod tm -compatible expansion ports configurable for a uart interface. the ic is a +3.3v esd-protected transceiver intended for half-duplex rs-485 communication up to 40mbps*. these transceivers are optimized for high speeds over extended cable runs, while maximizing tolerance to noise. the ic features symmetrical fail-safe and larger receiver hysteresis, providing improved noise rejection and improved recovered signals in high-speed and long- cable applications. * the maximum communication speed of this module is generally less than 10mbps due to the presence of current-limiting resistors on the data lines of this module and possibly also the host board. refer to the max14840e ic data sheet for detailed infor - mation regarding operation of the ic. features s half-duplex rs-485 transceivers s 40mbps maximum data rate s large (170mv) receiver hysteresis s symmetrical fail-safe receiver input s hot-swap capability s short-circuit-protected outputs s thermal self-protection s extended esd protection for rs-485 i/o pins s 6-pin pmod-compatible connector (pmod interface type 4 uart) s example software written in c for portability s rohs compliant s proven pcb layout s fully assembled and tested _________________________________________________________________ maxim integrated products 1 MAX14840PMB1 peripheral module 19-6338; rev 0; 5/12 ordering information appears at end of data sheet. pmod is a trademark of digilent inc. MAX14840PMB1 peripheral module for pricing, delivery, and ordering information, please contact maxim direct at 1-888-629-4642, or visit maxims website at www.maxim-ic.com.
designation qty description c1 1 1 f f q 10%, 10v x7r ceramic capacitor (0603) tdk c1608x7r1a105k c2 1 0.1 f f q 10%, 16v x7r ceramic capacitor (0603) murata grm188r71c104ka01d j1 1 6-pin right-angle male header j2 1 2-position terminal block on-shore technology ed500/2ds designation qty description jp1 1 2-pin straight male header r1Cr4 4 150 i q 5% resistors (0603) r5 1 120 i q 5% resistor (1206) u1 1 40mbps, +3.3v, rs-485 half- duplex transceiver (8 so) maxim max14840easa+ 1 shorting jumper 1 pcb: epcb14840epm1 supplier phone website murata electronics north america, inc. 770-436-1300 www.murata-northamerica.com on-shore technology, inc. 480-921-3000 www.on-shore.com tdk corp. 847-803-6100 www.component.tdk.com pin signal description 1 re receiver-enable input. this active-low pin enables the half-duplex receiver. 2 di driver input. this pin carries the transmit data from the pmod systems uart transmitter to a connected receiver. 3 ro receiver output. this pin carries the half-duplex receive data to the pmod systems uart receiver. 4 de driver-output-enable input. this active- high pin enables the half-duplex transmitter. 5 gnd ground 6 vcc power supply pin signal description 1 rs485-a noninverting rs-485 signal 2 rs485-b inverting rs-485 signal _________________________________________________________________ maxim integrated products 2 component list component suppliers note: indicate that ou are using the mpm hen contacting these component suppiers. detailed description uart interface the MAX14840PMB1 peripheral module can interface to the host by plugging directly into a pmod-compatible port (configured for uart ) through connector j1. connector j1 provides connection of the module to the pmod host through an interface similar to the pmod uart type 4 standard recommended by digilent. the transmit driver and receive pin assignment are the same as the standard. however, the cts and rts signals are replaced by half-duplex driver- and receiver-enable signals. see table 1. connector j2 provides the rs-485 positive and negative signal pair. see table 2. table 1. connector j1 (uart communication) table 2. connector j2 MAX14840PMB1 peripheral module
re de di ro vc c gn d ro 1 re 2 de 3 di 4 vc c 8 gn d 5 a 6 b 7 m ax1 48 40 e u1 gn d vc c 12 0 r5 1 2 j2 vc c gn d 15 0 r1 15 0 r2 15 0 r3 15 0 r4 1 2 3 4 5 6 j1 0. 1uf c2 1u f c1 1 2 jp 1 gn d vc c a b rs48 5- a rs48 5- b _________________________________________________________________ maxim integrated products 3 connector jp1 (termination select) this jumper port optionally inserts a 120 i termination resistor across the transmit-positive and negative nets. the jp1 jumper should be installed at the endpoints of the rs-485 network, and not at the midpoints. software and fpga code example software and drivers are available that execute directly without modification on several fpga devel - opment boards that support an integrated or synthe - sized microprocessor. these boards include the digilent nexys 3, avnet lx9, and avnet zedboard, although other platforms can be added over time. maxim provides complete xilinx ise projects containing hdl, platform studio, and sdk projects. in addition, a synthesized bit stream, ready for fpga download, is provided for the demonstration application. the software project (for the sdk) contains several source files intended to accelerate customer evalu - ation and design. these include a base application (maximmodules.c) that demonstrates module functionality, and which uses an api interface (maximdevicespecific utilities.c) to set and access maxim device functions within a specific module. the source code is written in standard ansi c format, and all api documentation including theory/operation, register description, and function prototypes are documented in the api interface file (maximdevicespecificutilities.h & .c). the complete software kit is available for download at www.maxim-ic.com . quick start instructions are also available as a separate document. figure 1. MAX14840PMB1 peripheral module schematic figure 2. MAX14840PMB1 peripheral module component placement guidecomponent side MAX14840PMB1 peripheral module
_________________________________________________________________ maxim integrated products 4 figure 5. MAX14840PMB1 peripheral module pcb layoutinner layer 2 (power) figure 3. MAX14840PMB1 peripheral module pcb layoutcomponent side figure 4. MAX14840PMB1 peripheral module pcb layoutinner layer 1 (ground) MAX14840PMB1 peripheral module
_________________________________________________________________ maxim integrated products 5 figure 6. MAX14840PMB1 peripheral module pcb layoutsolder side figure 7. MAX14840PMB1 peripheral module component placement guidesolder side MAX14840PMB1 peripheral module
part type MAX14840PMB1# peripheral module _________________________________________________________________ maxim integrated products 6 ordering information # denotes rohs compliant. MAX14840PMB1 peripheral module
revision number revision date description pages changed 0 5/12 initial release maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a maxim product. no circuit patent licenses are implied. maxim reserves the right to change the circuitry and specifications without notice at any time. maxim integrated products, 120 san gabriel drive, sunnyvale, ca 94086 408-737-7600 7 ? 2012 maxim integrated products maxim is a registered trademark of maxim integrated products, inc. revision history MAX14840PMB1 peripheral module
|
